Adafruit Feather M0 Adalogger

Adafruit Feather M0 Adalogger

Plus de détails

prix total

ADA-02796

27,00 € TTC

2 pièces disponibles

Attention : dernières pièces disponibles !

Quantité de 1 à 4 de 5 à 9 de 10 à 19 de 20 à 49 de 50 à +
Prix 27,00 € 26,46 € 26,19 € 25,65 € 25,11 €

Feather is the new development board from Adafruit, and like its namesake it is thin, light, and lets you fly! We designed Feather to be a new standard for portable microcontroller cores.

 

This is the Adafruit Feather M0 Adalogger - our take on an 'all-in-one' Cortex M0 datalogger (or data-reader) with built in USB and battery charging. Its an Adafruit Feather M0 with a microSD holder ready to rock! We have other boards in the Feather family, check'em out here

 

At the Feather M0's heart is an ATSAMD21G18 ARM Cortex M0 processor, clocked at 48 MHz and at 3.3V logic, the same one used in the new Arduino Zero. This chip has a whopping 256K of FLASH (8x more than the Atmega328 or 32u4) and 32K of RAM (16x as much)! This chip comes with built in USB so it has USB-to-Serial program & debug capability built in with no need for an FTDI-like chip.

 

To make it easy to use for portable projects, we added a connector for any of our 3.7V Lithium polymer batteries and built in battery charging. You don't need a battery, it will run just fine straight from the micro USB connector. But, if you do have a battery, you can take it on the go, then plug in the USB to recharge. The Feather will automatically switch over to USB power when its available. We also tied the battery thru a divider to an analog pin, so you can measure and monitor the battery voltage to detect when you need a recharge.

 

Here's some handy specs! Like all Feather M0's you get:

Measures 2.0" x 0.9" x 0.28" (51mm x 23mm x 8mm) without headers soldered in

Light as a (large?) feather - 5.3 grams

ATSAMD21G18 @ 48MHz with 3.3V logic/power

256KB of FLASH + 32KB of RAM

No EEPROM

3.3V regulator with 500mA peak current output

USB native support, comes with USB bootloader and serial port debugging

You also get tons of pins - 20 GPIO pins

Hardware Serial, hardware I2C, hardware SPI support

8 x PWM pins

10 x analog inputs

Built in 100mA lipoly charger with charging status indicator LED

Pin #13 red LED for general purpose blinking

Power/enable pin

4 mounting holes

Reset button

 

The Feather M0 Adalogger uses the extra space left over to add MicroSD + a green LED:

 

Pin #8 green LED for your blinking pleasure

MicroSD card holder for adding as much storage as you could possibly want, for reading or writing.

 

Comes fully assembled and tested, with a USB bootloader that lets you quickly use it with the Arduino IDE. We also toss in some header so you can solder it in and plug into a solderless breadboard. Lipoly battery, MicroSD card and USB cable not included (but we do have lots of options in the shop if you'd like!)

 

22.8mm x 51.6mm x 8mm / 0.9" x 2.0" x 0.28"

Weight: 5.3g

 

Toute l'information sur le site officiel ici.

 

Kit à souder livré dans un emballage ESD à Zip réutilisable.

Comme tous nos produits, ce kit est RoHS.

Logo RoHS

Aucun commentaire n'a été publié pour le moment.

Seuls les utilisateurs enregistrés peuvent poster des commentaires.